-
Devulapalli Balaji (1989);
Thesis topic:" Mathematical modelling of combination blown
steelmaking processes."
-
Amarendra Kumar Singh
(1990); Thesis topic:" Mathematical modelling of thermal fields
during heat treatment of steel"
-
Chaitanya
Bhanu(1997); Thesis topic: "Hydrodynamic modelling of steelmaking
tundish systems"
-
Rakesh Kumar (1997);
Thesis topic: "Modelling of mixing and mass transfer phenomena in
gas agitated reactors" ( Co-supervisor: Prof. B.Deo, Dept. of MME,
IIT, Kanpur)
-
Asish Robert (1998);
Thesis topic: "Mathematical Modelling of flow and Residence Time
Distributions in different tundish designs" .
-
Kamalesh Mandal
(1998); Thesis topic: "Physical and mathematical modelling of flow
and mixing in CAS systems with large aspect ratio"
-
Binod Bihari Mahato
(2001); Thesis topic:"Modelling of flow and mixing in gas stirred
ladle under transient conditions
-
Projit Mitra (2001);
Thesis topic: "Mathematical Modelling of three dimensional turbulent
flows in some steelmaking operations
-
Santosh K Rout
(2001); Thesis topic: "Modelling of steady and transient flows in
gas stirred ladle systems"
-
Jayanta Mandal
(2003); Thesis topic: "Mixing times in ladles stirred with dual
porous plugs"
-
D. Satish (2003);
Thesis topic: "Flow, mixing and mass transfer in dual plug stirred
ladles in the presence of an upper buoyant slag phase"
-
M. Madan (2004);
Thesis topic: "Numerical simulation of flow phenomena in rotating
viscometers"
-
D.Chatterjee (2005);
Thesis topic: " A computational and experimental study of fluid flow
phenomena in a hollow jet Nozzle"
-
Sujoy Patil (2005);
Thesis topic: " Mixing models for slag covered ladles"
-
Rajeev K Singh
(2007); Thesis topic: "Mathematical Modeling of fluid flow, mixing
and hydro0dynamic refractory wear in gas stirred ladles for
different bottom designs"
-
S. Anand (2008);
Thesis topic: "Fluid flow and residence time distributions in two
different slab casting tundish designs"
-
A. Muthuchammy
(2009); Thesis topic: " A thermo chemical model for charge
proportioning in an energy optimizing furnace"
-
K. Rajasekar (2009); Thesis
topic: "Modeling of inclusion removal kinetics in steelmaking tundish"
-
M. Peranandhanathan
(2010); Thesis topic: "Slag eye area: measurements and correlations"
-
Sumanta Bagui (2010);
Thesis topic: "The role of a near wall dam on the metallurgical
performance of slab caster tundish"
-
Ranjeet K.Singh
(2010); Thesis topic: "Measurements and modeling of heat flow in high
temperature furnace and steelmaking reactors"
-
Bapin K Rout (2011);
Thesis topic: "Physical modeling transport processes in an energy
Energy Optimizing Steelmaking Furnace"
-
Ishant Jain (2011);
Thesis topic: "Thermal modeling and measurements in high temperature
steelmaking operations"
-
Anurag Nandwana
(2011); Thesis topic: "Physical and mathematical modeling of fluid
flow phenomena in slab casting mold of different section size
(>1500mm)
-
Aniket Dutt (2012);
Thesis topic: "The role of tundish design on residence time
distributions (RTD) and slag entrainment phenomena"
-
SharvanaKumar R
(2012); Thesis topic: "Modeling and optimization of argon rinsing
practice in ladle metallurgy steelmaking operations"
-
A Murlikrishna
(2012); Thesis topic: "Physical modeling of grade intermixing
phenomena in a four strand bloom casting tundish"
-
P. Dhandapani (2013);
Thesis topic: "Modeling and Optimization of slag eye area and mixing
time in ladle metallurgy steelmaking"
-
Suvajit Choudhary
(2014);Thesis topic: "Modeling of material and thermal mixing in
steelmaking tundish systems".
-
Goutam Mandal
(2014);Thesis topic: "Modeling and measurement of heat flow during
solidification of metals and alloys".
-
Pari R (2014); Thesis topic:"Modeling and measurement of intermixing time in a slab
casting tundish fitted with different flow control devices".
-
Soumava Chakraborty
(2015); Thesis Topic: "Modelling of solidification of large,
round steel ingots and validation against industrial scale
measurements".
-
Lipsa Das (2016);
Thesis Topic: "Simultaneous teeming of two ladles into a launder,
hydrodynamic, thermal and material mixing".
-
Rishikesh Mishra (2016:BT-MT);
Thesis Topic: "Physical and Mathematical Modeling of slag
entrainment during drainage of steelmaking ladles".
-
Rohan Sharma (2016:BT-MT);
Thesis Topic: "Transient multiphase modelling of tundish
hydrodynamics during end of sequence casting operation".
-
Krashnavtar (2017:BT-MT);
Thesis Topic: "Mathematical modelling of grade intermixing phenomena
in a four strand bloom casting tundish"
(Best Master Degree thesis award in Materials and
Metallurgical
Engineering, IIM, 2017).
-
Subham Ranjan (2017:
BT-MT);
Thesis Topic: "Inert gas injection into steelmaking tundish and
possible improvement in steel cleanliness".
-
Rohit Kumar Tiwari
(2018); Thesis Topic: "Fluid dynamic and thermal modelling of
homogeneous and two phase flows in ladle shroud".
-
Sayantan Chakraborty
(2019); Thesis Topic: "Physical and mathematical modelling of
intermixing time in steelmaking tundish under throughput rate".
-
Zunaid Alam (2020);
Thesis Topic: "Modelling of flow mixing in a mechanically agitated
steelmaking ladle and comparison with equivalent gas stirred ladle".
-
Chandan Kumar (2021);
Thesis Topic: "The effects of inert gas shrouding on the behavior of
free jet length, tundish open eye and penetration depth: Physical
modeling and numerical analysis".
-
Ankur Agnihotri (2022);
Thesis Topic: "Tundish process performance evaluation via
numerically predicted RTD and its correspondence with plant scale
measurement".
