| 1. |
Naveen, Gopal Voruganti |
Devlopment and Characterisation of Jute Sandwiched Structure |
2005 |
| 2. |
Rajeev Sharma |
Design of Bus Fascia made of Sandwiched FRP |
2005 |
| 3. |
Deep, K. S |
Determination of Limiting Blank Holding force and Cavity pressure in Hydromechanical Deep Drawing |
2005 |
| 4. |
Kumar, Rajesh |
Microstructural Characterization of Deep Drawn Low Carbon Steel |
2006 |
| 5. |
Tailor, Piyushkumar B |
Performance Evaluation of Abrasive Flow Machining |
2006 |
| 6. |
Kulkarni Sumedh Suresh |
Experimental Investigation of Formability Enhancement Using Warm Deep Drawing |
2006 |
| 7. |
Mondal, Subrata |
Experimental Investigation on Modified AFM Process |
2007 |
| 8. |
Pandya, Chinmay |
Numerical simulation of the Degradation Behavior of Carbon-Carbon composites during Carbonization Process |
2007 |
| 9. |
Singh, Jitendra Kumar |
Characterization of FRP-Joints |
2007 |
| 10. |
Akhtar, Syed Nadeem |
Fabrication and Modeling of Ionic Polymer Metal Composites for use as Actuators |
2007 |
| 11. |
Varghese, Anil |
Investigations into rotatory assisted Abrasive Flow Machaning (RA-AFM) process |
2008 |
| 12. |
Nair R, Sandeep |
Finishing of shafts for Ultra High Speed for gas bearings |
2008 |
| 13. |
Roy, S. Dutt |
Theoretical modeling on magnetic abrasive finishing process |
2009 |
| 14. |
Cholla, S. Chandra Bose |
Investigation of optimizing parameters for blind pocket milling using abrasive water jet machining |
2009 |
| 15. |
Mankad, Tarun |
Exploring vibrational aptitude and atto-gram mass sensing ability of composite nano-pillars |
2009 |
| 16. |
Katiyar, Jitendra Kmr |
Novel synthesis of Micro- and Nano- Granular Fe-Cu alloy by Electric Discharge Machining |
2010 |
| 17. |
Chandra Sekar Sathua |
Magentic Abrasive Finishing (MAF) |
2011 |
| 18. |
Omprakash Rawat |
Electric Discharge Machining |
2011 |
| 19. |
Sathish Sekar |
"DRIFT" THREE WHEELER FOR A GREEN RIDE |
2011 |
| 20. |
Virender Singh Kanwal |
Design of Multidetector system for gamma ray imaging and nuclear safety. 2012 |
2012 |
| 21. |
Sairam Jagatani |
Design and Development of an Interactive Board Game, Taking Inspiration from Ideas of Indian Logics |
2012 |
| 22. |
Jitendra Singh |
Fabrication of Complex Circuit Using Electrochemical Micro Machining on Printed Circuit Board (PCB) |
2013 |
| 23. |
M. Jeyakumar |
Design of math products to impart spatial understanding in children |
2013 |
| 24. |
Charchit Kumar |
Fabrication and flow analysis of micro channels for bipolar plate of polymer electro lyte membrane fuel cell |
2013 |
| 25. |
Rehan Ahmed Shaikh |
Data error Analysis of in house built multidector gamma ray CT scanner using first Kanpur theorem |
2013 |
| 26. |
Devaki Nandan |
Vibration assisted plasma arc machining of mild steel |
2014 |
| 27. |
Neha Singh |
Magnetic Abrassive finishing of micro channel |
2014 |
| 28. |
Randheer K. Saha |
Fabrication of Ground composites |
2014 |
| 29. |
Dharmesh Kumar |
Excimer laser shock penning of Ti Alloys |
2014 |
| 30. |
Ravi K. D. |
Multi-objective optimization of EDM parameters on Machining carbon-carbon composites |
2014 |
| 31. |
Binit Kumar |
Severe Plastic Deformation (Friction Stir Deformation) |
2015 |
| 32. |
Aswani Kumar |
Surface texturing of Ti alloys using fiber laser |
2015 |
| 33. |
Bhagath P. Paparoa (M.Des.) |
Designing products for physically challenged to enhance the Usability & Aesthetics |
2015 |
| 34. |
Shivakumar M (M.Des.) |
Peltify-Design & Development of Wearable Personal Cooling & Heating device |
2015 |
| 35. |
Pankaj Kushwaha (M.Des.) |
Design and manufacturing of an indigenous MALE unmanned aerial vehicleand weight reduction through controlling different variables |
2015 |
| 36. |
Pratik Murkute (MSP) |
Tribo corrosion Study of material used in naval application |
2016 |
| 37. |
Vishal Kumar |
Maintainability Study on Advanced Materials for Aerospace Applications – Inconel-625 and gamma-TiAl |
2016 |
| 38. |
Parashtekar Alhad (MSP) |
Development of experimental methodology to Determine the optimum Mechanical operating Pressure for an electrolyser |
2016 |
| 39. |
Sudhanshu Mathur (MSP) |
Electric discharge turning |
2016 |
| 40. |
Deepti Sharma (MSP) |
Finishing of helical gears using Abrasive Flow Finishing |
2016 |
| 41. |
S. Gowthaman(MSP) |
Effect of Attenuating Medium on the Tribology of Laser Peened Armoured steel |
2017 |
| 42. |
Kumar Ravi (MSP) |
Surface micro-channeling of metals via Electro-chemical dissolution |
2017 |
| 43. |
Parameswari Gundavarapu |
Nano finishing of flat and free form surfaces |
2017 |
| 44. |
Dhananjay Dubey (MSP) |
Finishing of Ball Using Abrasive Flow Finishing |
2017 |
| 45. |
Ambuj Shah (MS by R) |
Numerical Study of Transient Thermo-Fluidic Behaviour of the Melt Pool during Laser Welding |
2017 |
| 46. |
Aakash Tyagi (MS by R) |
Theoretical and Experimental Study of Wire Electrochemical Turning Process |
2017 |
| 47. |
Mahavir Singh |
Thin Wall Micromachining of Ti-6Al-4V using Wire Electrical Discharge Machining Process |
2018 |
| 48. |
Shashank Sharma |
A Multiphysics Numerical Model for Melt Hydrodynamics in Selective Laser Melting |
2018 |
| 49. |
Gaganpreet Singh |
Fabrication of flexible absorber using screen printing technology |
2018 |
| 50. |
Vyom Sharma |
Theoretical and Experimental Analysis of Wire Electrochemical Micromachining (Wire-ECM) Process |
2018 |
| 51. |
Mahesh A. Thalkar (MS by R) |
Micro patterning of large surface area using multiple electrode electrochemical micro machining |
2018 |
| 51. |
Pradeep Kumar Sahu (MS by Research) |
Jet Electrochemical Machining |
2019 |
| 52. |
Prabhu Dayal(MSP) |
Electrochemical Milling |
2019 |
| 53. |
Kavita Yadav (MSP) |
Modeling of Magnetic Assisted EDM process |
2019 |
| 54. |
Shirale Arvind Shivaji (MSP) |
Minimum Quantity Lubrication |
2019 |
| 55. |
Gopal Ashok Gupta (MSP) |
Preferential Media For Abrasive Flow Machining |
2019 |
| 56. |
Brahmesh Joshi |
End-of-Life Analysis of Automobile Lead-Acid Batteries: A System Dynamics Approach |
2019 |
| 57. |
Deepak Mishra |
Automation of the Excimer Laser Micromachining and Two Photon Polymerization process for large area fabrication |
2019 |
| 58. |
Rohit Kumar Sahu |
Influence of Zirconia (ZrO2.8Y2O3) Coating on the Copper Tool in EDM Machining |
2021 |
| 59. |
Krishnakant Yadav |
Generation of a textured surface using Wire Electrochemical Micromachining and analysis of the wetting behaviour |
2022 |
| 60. |
Parth Luwaria |
Permeation of air through a graphene sheet: a molecular dynamics study |
2023 |
| 61. |
Mohammad Shahid Khan |
Improving Efficiency of Pneumonia Detection in Chest X-Rays Using Convolutional Neural Networks Based Deep Learning Model |
2023 |
